Last Week’s Moto Trip

August 26, 2015

With orders, emails, and messages finally back under control, last week seemed like a good time to sneak out of the office for a ride.  All of us here at Mosko are trying to squeeze in a little time-off before summer ends: Andrew’s in British Columbia canoeing and camping, Nicole is camping & crabbing at the coast, and Lee’s prepping for a BDR trip in a few weeks.  In the meantime, Tiffany has been holding down the fort (thank you Tiffany!!).

For my ride, I followed the Cascade Discovery Route and connected it to the Oregon Backcountry Discovery Route #3 down to California.  There’s a quick & dirty trip report here on advrider.com, and some pics below.  I took a Reckless 80, but rigged a Scout 30 duffle instead of the included drybag, which basically doubles the capacity of the rear bag.  I didn’t need all that capacity, but wanted to experiment to see if it worked (it did), because people have been asking.

I took the Hubba NX (one person) tent.  I have a Gear Shed that goes with this, but with it being summer, and no rain in the forecast, I left that at home.  That’s one of the really cool things about using the Hubba Nx and Gear Shed instead of a two or three-person tent.  When the weather’s good, you can leave your Gear Shed at home and just take the tent, which packs tiny.

Lately I’ve been rigging my Whisperlite Universal stove to run on canisters instead of unleaded gas.  I did this because a) I got tired of my hands getting all sooty from the burnt unleaded gas and b) the jets rarely clog on canisters, and c) canisters don’t require priming.  But I still really dig how the Whisperlite Universal can go either way – canister or liquid – based on what kind of trip I’m on.  Like for example, when I’m traveling internationally I run it off unleaded because that’s all I can find.  But here in the US for local trips, canisters are pretty damn convenient.

I also used my Autoflow gravity fed water filter every day.  This is so much better than pumping an old-school filter.  And because I have the filter with me I can run with a lot less water on the bike which saves a lot of space and weight.  I was carrying 2-4 liters less than I would have without the filter.

I took the protoype of our new tool roll.  We’re making some tweaks to this, adding additional pockets and improving the closure system, but overall it worked great and it fit all my tools, which were in a Kriega roll before.  I love that it’s sized perfectly to slide in the rear pockets on our Reckless 80 and Backcountry 35 Pannier.

Tire iron pockets on the outside are really handy.

This has been a busy summer, with a lot of time spent in the “business of” motorcycles, but not enough time actually riding.  Glad to finally catch up on some riding time and reconnect with my bike last week.  I’m stoked for another trip in a few weeks in Colorado with Kurt from Black Dog Cycleworks & Dusty after the KTM rally in Crested Butte.

Summer’s on!  Hope everyone’s out enjoying it!!

Outdoor Retailer Show

August 11, 2015

Last week I flew down to Salt Lake City for the Outdoor Retailer (OR) trade show.  It’s a big show, around 25-30,000 attendees, and it’s mostly a venue for outdoor product retail stores to connect with their suppliers: i.e. makers of tents, kayaks, SUPs, stoves, backpacks, fishing gear, etc. However a portion of the show is devoted to “sourcing,” where designers like us can connect with factories, fabric mills, and hardware makers.   I was on the hunt for new fabrics and hardware to use in bags/apparel, and also looking for a welding factory to help with some new bag designs in the pipeline.

Here’s a couple shots of the show.  I could’ve easily spent another day there just geeking out on all the cool camping gear and bags.  No time for that on this trip though.

Found some cool urethane fabrics to use in a future iteration of our drybags.

A wall of buckles.

Spent a lot of time flipping through wall hangers and swatch books like this one.

Some highly abrasion resistant yarns

Got to meet James Rittenhouse, the inventor of MOLLE Stix.  Awesome product, thank you sir!!

This is another of James’ inventions.  It’s a single buckle that you can pull and to release as many additional side release buckles as you want simultaneously.

Also visited with another of our hardware vendors to check out some new products, like this heavy duty buckle (700+lbs).

And this sewn-in magnetic closure they’re working on.

I really enjoyed the trip to OR, well worth the time/money.  It was also cool to run into so many other Hood River/White Salmon people either in their booths or walking the halls.  My buddy Rob was nice enough to let me crash on the couch in his hotel room.

New Wedge & Frame

Last week, Lee mounted the rapid prototype of our new wedge/frame and loaded up his Backcountry 35s with logs (38 pounds per side) and took them out for some bumpy high speed riding.

Everything held up great.  Can’t wait until we can get these things into production.

Here’s a new latch we’re looking at for the wedge mount system.  It can accommodate a padlock, and would be anodized black.

Fabric Creation

The apparel project is finally back in motion.  We’re working with a product development company in Portland.  We were so incredibly frustrated with our inability to find a fabric that we liked that we’ve decided to create our own 3-layer fabric from scratch.  Which means literally selecting a yarn, a weave, a finish, a membrane, and an inner fabric.  We’ll be working with a mill to design a new material from the ground up, which should be interesting.  By doing that we can specify the abrasion resistance, the waterproofing level, the breathability, and any other features we want. The initial fabric design brief will look something like this.

Main Body Fabric

• Waterproof (20,000+)
• Breathable (highest possible MVTR)
• Highly abrasion resistant, holds up in a crash
• Heavyweight, won’t flap in wind
• Comfort, Stretch
• Moisture Management & Antimicrobial Inside
• Reflectivity (ideally invisible)

High Abrasion Areas

• Superfabric at shoulders, knees, elbows, hips, butt, calf, shin
• Inside of pant leg: leather or similar material for heat resistance, abrasion, and bike contact.

Armor Liners

• Mesh, good airflow
• Anti microbial
• Moisture management

Inner Rain Liner & Outer Rain Pant

• Waterproof/Breathable
• 2 or 3 Layer
• Lightweight
• Packs small when not in use
• Inexpensive to replace if damaged

Jersey(s)

• Mesh, good airflow
• Anti-microbial
• Moisture management

Summer’s flying by.  I’ve been feeling a strong urge to get out and do some riding.  Planning a local trip of some kind next week.  Not sure exactly what or where, but something involving dirt, tents, and motorcycles.

BMW, Billings, & Back

August 1, 2015

Just got back from a trip to Montana for the BMW Motorcycle Owners Association event in Billings.  Long solo road trip, and another awesome event for Mosko.  It felt kind of weird to leave the office for a week when we have so much going on back home, but because of our direct sales model, these events are even more important for us than they are for other vendors.  And it’s better when we can drive instead of fly, because we can take a show bike (key for doing demos) plus bring inventory to sell cash & carry.

Billings BMWMOA

Got the trailer all loaded up with inventory and a bike.

Man when it rains in Montana it really rains.

Loved having a corner booth for once.

This customer brought in the bag on the left after a 65 mph pavement slide.  She was fine.  The outer bag took a beating but the inside liner was 100% in tact, no holes at all, and the mounts were fine.  She rode to BMWMOA with the bag.  We took off the mounts, hooked them up to a new bag, and got her back on the road for $100.  This was about as good of a crash test as we could ever ask for and now we have a cool bag to show off when people ask about crash testing.  Replacing a $100 outer bag is a lot better than replacing a $600 hard bag.

Another customer brought in these cool MOLLE side release D-Rings to show us.  She found them on a tactical website.  Love these things.  They enable you to turn any MOLLE panel into an tie-down point for straps so, for example, you could tie down a thermarest or tent to the top MOLLE panel on a Backcountry Duffle.  In the future it would be cool to research what other stuff like this is out there and maybe offer it for sale on our website.

Also experimented with the new Backcountry 30L duffle as a pannier topper on the BMW hard cases.

And then back on the road home!

I was totally exhausted after this show.  Setting up, tearing down, and working the show solo all day doing demos really took it out of me (John Murakami, THANK YOU for your help tearing down and also for manning the booth so I could run out and grab food).  Plus I was getting up early in the morning to go running before the show and I got a week-long membership at a local gym, so I was working out in the evenings too.  Really long days.   Stopped on the way home to spend a night on this river, read, and just generally chill out.

Richard Siberell Visit

On the way to Billings, I stopped in Bozeman to visit with Richard Siberell, an independent outerwear designer we’ve been in touch with over the last 6 months.  Richard is a moto guy, he was one of our first customers.  He has a killer apparel design shop with all kinds of sewing, seam sealing, and welding equipment, and is by far the most knowledgeable person I’ve ever met when it comes to cutting-edge outerwear design.  As we’ve been out researching and talking to people about apparel design and fabric development his name comes up constantly. He’s worked for some of the world’s most respected outdoor gear companies and is currently splitting his time between Patagonia and Sitka Gear.  He is an awesome host: I learned a ton and even got to eat some of the elk he shot for dinner.  Richard: thank you!!  I’d love to return the favor if you ever come west.

Richard’s shop.

Checking out our jacket prototype under a microscope.

Some light reading…

I love that so many people from the outdoor industry are into moto.  It’s a trip.  Motorsports are surprisingly well represented in the management and design teams at major backpacking and outdoor product companies.  I just found out that the founder of arcteryx is currently on a round-the-world dualsport trip of indeterminate length.

Here’s a cool version of the Reckless 80 that Richard sewed himself.

Complete with MOLLE bags.

S Group

Back in the Northwest we went into Portland to meet with the S-Group, a product development company in Portland that is helping us take the apparel project through completion. Andrew and I have been tapped-out time-wise, so we reached out to S Group for help.  They work with two other outdoor apparel companies we know well.  There’s going to be a lot more about the S Group in future posts.

Frame/Wedge Redesign

Lee has been working hard in the background to redesign our mounting frame and wedge as injection molded pieces instead of milled.  This week we got back our rapid prototypes and they look really, really good.  These were 3D printed in glass-filled nylon, which is the same material we’ll use in production.  The 3D printed proto’s strength is only about 1/3rd of what it will be in production, but it gives us a chance to test them before we pay for an expensive mold.  If you’ve never seen 3D printing technology, I highly recommend googling it… it’s amazing.  This was my first experience with it and I’m totally blown away by these prototypes.

We’re adding some thickness in the redesign.  The beveled part in the pic below is the same as on the current wedge, the flat part is the additional width.

Tool Bag

We also got another round of prototypes on our tool bag and tool roll.  We added these tire iron storage spots on the outside of the roll.

The tool bag will have a hook on top so it can hang off the beavertail like this.

Added this expandable storage on the outside for large tools and/or tire irons.

Also these pockets on the outside for tube patches and other flat stuff like that.

We’re working on a drybag MOLLE bag that the tool rolls will fit into.  This also works as a standalone bag as well.

Reckless Revisions & Videos

We’re currently working on Reckless 80 revisions for the next production run (these will not available until sometime next year, we’re going to stock out on the R80 for 4-6 months starting soon).  The buckles and straps on the center harness will become removable/replaceable, connected using aluminum stiffeners just like the cam buckle straps on the legs currently are. We’re also experimenting with an open hole of some kind to accommodate rear-fueling bikes, and daisy chains so you can strap down anything you want in this area if you’d prefer to use a different type of center bag.  We’re also looking for a new welding company to make the drybags with molds instead of the hand-feed welding on the current drybags.  The molded seams will give more consistent, stronger, cleaner looking welds.

Also we want to change these corners on the beavertail.  This is a potential failure point on thin-profile bikes, where this part of the bag can accidentally become semi-load-bearing.  Plus it just looks kind of weird.

Thinking we’ll replace it with webbing and a sliding buckle so it can be adjusted to the specific bike.  Kind of like the stabilizing straps at the top of a backpacking pack shoulder strap.

Assembly

Lee has been spending a lot of time in Portland overseeing the assembly of panniers from our most recent shipment.   We’re currently about half way through.  Big job!

I’m back for a few more days, then off for my first-ever visit to the huge Outdoor Retailer trade show in Salt Lake City next week.  That should be interesting.  I’m just there to walk the show, look at fabrics, and learn.  Stoked for that.